Product Description
Foot Length(cm/inch) | UK | US | AU | CA | EU |
24.5/9.65 | 5.5 | 6.5 | 5.5 | 6.5 | 39 |
25/9.84 | 6 | 7 | 6 | 7 | 40 |
25.5/10.04 | 6.5 | 7.5 | 6.5 | 7.5 | 40.5 |
26/10.24 | 7 | 8 | 7 | 8 | 41 |
26.5/10.43 | 7.5 | 8.5 | 7.5 | 8.5 | 42 |
27/10.63 | 8 | 9 | 8 | 9 | 42.5 |
27.5/10.83 | 8.5 | 9.5 | 8.5 | 9.5 | 43 |
28/11.02 | 9 | 10 | 9 | 10 | 44 |
28.5/11.22 | 9.5 | 10.5 | 9.5 | 10.5 | 44.5 |
29/11.42 | 10 | 11 | 10 | 11 | 45 |
29.5/11.62 | 10.5 | 11.5 | 10.5 | 11.5 | 45.5 |
30/11.81 | 11 | 12 | 11 | 12 | 46 |
30.5/12 | 11.5 | 12.5 | 11.5 | 12.5 | 47 |
31/12.2 | 12 | 13 | 12 | 13 | 47.5 |
This PTC ceramic fan heater heats electrically.
Technical details:
Power: 45W/1000W/2000W
Fast heating in 3 seconds.
60° oscillation function for even heating.
3 modes.
1-stage natural wind 45 W, circulating air, cooling machine.
2-level low heat 1000 W, pleasantly warm air, warm enjoyment.
3-level high heat 2000W, strong hot wind, not afraid of severe cold.
Temperature range: 15℃~45℃
Overheat protection, dumping power failure protection.
Power supply: 220V
Fan heater with 8 hour timer
Installation process:
1. Remove the base from the box.
2. Align the front footrest with the rear footrest, align the holes and insert firmly.
3. Fix the four holes with screws.
4. Pass the power cord through the hole in the center of the base and align the hole with the hole between the rear base.
5. Four Hole Alignment.
6. Turn it so that the four buckles are attached and the two holes in the middle are fixed with screws.
What should I do if the balls slide out in the base?
1) Using a Phillips screwdriver, loosen the three screws on the fixed rail.
2) Carefully open the ball cover.
3) Put the dropped ball in the groove.
4) Cover the cover and tighten the screws to install normally
Technical details:
Power: 45W/1000W/2000W
Fast heating in 3 seconds.
60° oscillation function for even heating.
3 modes.
1-stage natural wind 45 W, circulating air, cooling machine.
2-level low heat 1000 W, pleasantly warm air, warm enjoyment.
3-level high heat 2000W, strong hot wind, not afraid of severe cold.
Temperature range: 15℃~45℃
Overheat protection, dumping power failure protection.
Power supply: 220V
Fan heater with 8 hour timer
Installation process:
1. Remove the base from the box.
2. Align the front footrest with the rear footrest, align the holes and insert firmly.
3. Fix the four holes with screws.
4. Pass the power cord through the hole in the center of the base and align the hole with the hole between the rear base.
5. Four Hole Alignment.
6. Turn it so that the four buckles are attached and the two holes in the middle are fixed with screws.
What should I do if the balls slide out in the base?
1) Using a Phillips screwdriver, loosen the three screws on the fixed rail.
2) Carefully open the ball cover.
3) Put the dropped ball in the groove.
4) Cover the cover and tighten the screws to install normally
Recommended Products
(4.6)
$49.68 $77
Worldwide Delivery
35% off
(5)
$129.27 $134.44
Worldwide Delivery
3% off
(4.4)
$10.18 $10.38
Worldwide Delivery
1% off
(4.2)
$208.99 $384.54
Worldwide Delivery
45% off
(4.6)
$141.35 $200.72
Worldwide Delivery
29% off
(4.8)
$21.07 $39.61
Worldwide Delivery
46% off
(4.8)
$143.95 $280.7
Worldwide Delivery
48% off
(4.8)
$47.2 $59.47
Worldwide Delivery
20% off
(4.6)
$1105.94 $1769.5
Worldwide Delivery
37% off
(5)
$55.9 $65.4
Worldwide Delivery
14% off